Model: Stepper Motors and Accessories
This 5V DC 28BYJ-48 Stepper Motor is small, inexpensive and high-quality geared step motor. The 28BYJ-48 Stepper Motor and ULN2003 Stepper Motor Driver is a widely popular combination of the stepper motor and stepper driver, because of the stability and reliability of the system.Thia 28BYJ-28 s..
Rs.75
Out Of Stock
Model: Stepper Motor Drivers
This is Mega Pololu Shield or RAMPS for short. The 3D Printer Controller Board RAMPS 1.4 is designed to fit the entire electronics needed for a RepRap in one small package for a low cost. RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty of room for expansi..
Rs.265
Model: Stepper Motor Drivers
The A4988 driver Stepper Motor Driver is a complete micro-stepping motor driver with built-in converter, easy to operate. It operates from 8 V to 35 V and can deliver up to approximately 1 A per phase without a heat sink or forced air flow (it is rated for 2 A per coil with ..
Rs.72
Model: Stepper Motor Drivers
The Double BTS7960 43A H-Bridge High-Power Stepper Motor Driver Module is; a fully integrated high current H bridge for motor drive applications using the BTS7960 high current half bridge. the BTS7960 is part of the NovalithICTM family. This containing one p-channel high side MOSFET and one n-channe..
Rs.680
Model: Stepper Motor Drivers
The DRV8825 stepper motor driver carrier is a breakout board for TI’s DRV8825 micro-stepping bipolar stepper motor driver. The DRV8825 features adjustable current limiting, over-current and over-temperature protection, and six microstep resolutions (down to 1/32-step). It operates from 8.2 – 45 V an..
Rs.175
/01-250x250w.jpg "DRV8833 2 Channel DC Motor Driver Module Board 1.5A 3V-10V (red)")
/02-250x250w.jpg "DRV8833 2 Channel DC Motor Driver Module Board 1.5A 3V-10V (red)")
Model: Stepper Motor Drivers
DRV8833 is a dual H-bridge motor driver IC that can be used for bidirectional control of two brushed DC motors at 2.7 V to 10.8 V. It can supply up to about 1.2 A per channel continuously and can tolerate peak currents up to 2 A per channel for a few seconds, making it an ideal driver for small moto..
Rs.150
Model: Stepper Motor Drivers
The L9110S dual channel h-bridge motor driver module is a compact board that can be used to drive small robots. This module is based on L9110 Motor Driver IC. This module has two independent motor driver chips which can each drive up 800mA of continuous current. The boards can be operated from 2..
Rs.69
Model: Stepper Motor Drivers
This stepper motor driver is featuring TB6560AHQ new original chip. The TB6560AHQ has low voltage shutdown, overheating stop and overcurrent protection circuit to ensure optimal performance.The TB6560 stepper motor control circuit is the most commonly used current circuit, which can control a 2..
Rs.580
Model: Stepper Motor Drivers
TB6600 Arduino Stepper Motor Driver is an easy-to-use professional Stepper motor drive , which could control a two-phase stepping motor. It is compatible with Arduino and other microcontrollers that can output a 5V digital pulse signal.TB6600 Arduino stepper motor driver&nbs..
Rs.475
-250x250.jpg "ULN2003 Driver Module Stepper Motor Driver Board")
Model: Stepper Motor Drivers
This is ULN2003 Driver Module Stepper Motor Driver Board for driving and controlling stepper motors.ULN2003 Stepper Motor Driver Board uses the ULN2003 DARLINGTON ARRAYS to drive the 4-phase 5-wire stepper motor (5v-12v).It’s easy to use Arduino or another development platform to drive the step..
Rs.45
Showing 1 to 10 of 10 (1 Pages)